Small Scale Military Headquarters

That looks great! What’s the story on the foam foam rubber tracks? I must have missed that. I’ve been putting off my build because the tracks look very time consuming.

I think Matthew can tell you what they're made of, but they go together faster than the resin and pin tracks.
There are two pieces per side and they are glued together to make one full track per side. I like the look of the resin
but they take some time.
Build the Tiger its a nice kit, Matthew did a nice job.

Hey Guys,

No foam just a resin rubber that seems to be working out well.
But it is a 24 hour set up time for the rubber to cure.
I agree the hard resin piece by piece does look better but a days worth of work to use them.
The cast rubber , 5 minuets !!!!

pickelhaube wrote: ↑

Sun Apr 10, 2022 4:23 am

Hey Guys,

No foam just a resin rubber that seems to be working out well.
But it is a 24 hour set up time for the rubber to cure.
I agree the hard resin piece by piece does look better but a days worth of work to use them.
The cast rubber , 5 minuets !!!!

That sounds good, you selling them?

Not at this time.

Bummer.

Here is my latest consignment a mid war standard striped Jagdpanther.

Very nice looking Matthew! Have you used the AK interactive wash on these two Jagdpanthers?

normandy wrote: ↑

Fri May 27, 2022 7:02 am

Very nice looking Matthew! Have you used the AK interactive wash on these two Jagdpanthers?

Yes I did.

That looks great, the wash adds to a great custom and paint scheme.

My next consignments are 3 Sdkfz 222.
One was my first panzer gray coloring .
It was a little bit of a challenge but I worked things out and the next will be much easier.

Pickel yet again more outstanding work! I'll say it once more, the washes make a huge difference in the look of these models.
I need to practice a little with them before doing a major project.
Great job on these!

Thanks buddy

Looking for 1/18 M-10 n Stug 4 I have bottom chassis’s My email is Paul.Caruso [email protected] Look foward to hearing from you Thanks

EnP1980 wrote: ↑

Sat Dec 03, 2022 2:18 pm

Looking for 1/18 M-10 n Stug 4 I have bottom chassis’s My email is Paul.Caruso [email protected] Look foward to hearing from you Thanks

E-mail sent.

M-10 ? Is that the US M-10 or the German Ersatz M10 Panther disguised as the US M-10 Tank Destroyer?

EnP1980 wrote: ↑

Sat Dec 03, 2022 2:18 pm

Looking for 1/18 M-10 n Stug 4 I have bottom chassis’s My email is Paul.Caruso [email protected] Look foward to hearing from you Thanks

Sorry didn't see this till now email sent.

Never recieved your email still hoping to get an M-10 tank destroyer I have the bottom chassie with tracks My Email is [email protected] Thank You

EnP1980 wrote: ↑

Tue Mar 07, 2023 11:06 am

Never recieved your email still hoping to get an M-10 tank destroyer I have the bottom chassie with tracks My Email is [email protected] Thank You

Sorry about that.
I plan on revamping the m-10 this year but I am dealing with some health issues and I am still work on storm damage on my house.
I also want to do the ersatz M-10 on the Panther as well this year

Here is my latest consignment.
A Indy bike with my side car.








Here is the modified bike next to an original Indy bike.

Very nice looking Matthew! The first thing I see is the brake and clutch lever/handles in the correct position, something
that wasn't on the original kit. Then the gas can and mounting bracket.
I've got six of these and I see they need updating.

Thanks for spotting those details Normandy.
I also swapped out the cables for thinner ones.
I also made a wooden ( plastic ) floor platform.
I also made wire front fender braces.

I have about 40 hours into this little rascal.

Matthew are the added details just for this consignment or will they be offered for existing kits?

normandy wrote: ↑

Sat Jul 15, 2023 10:58 am

Matthew are the added details just for this consignment or will they be offered for existing kits?

I made the slat floor for this consignment.
If or when I remake the molds I will probably make it to go with the kit.
I guess I could make the fender wire as well .
The break handle flip would have to me done by the modeler.
It took 1-2 hours to do.