Battle Damaged TBF-1
-
- Corporal
- Posts: 52
- Joined: Sat Oct 16, 2004 11:40 pm
- Location: Arizona
Battle Damaged TBF-1
Well... My TBF-1 Avenger sustained some "battle damage". Lost the left horizontal stabilizer /elevator to my 55lb German Shepherd. (Didn't know the Germans were active the Pacific Theater)
I have tried to glue it using Testors Model Cement with no luck. Anyone have any glue recommendations for this consistency plastic?
Thanks.
I have tried to glue it using Testors Model Cement with no luck. Anyone have any glue recommendations for this consistency plastic?
Thanks.
Jagdflieger
-
- Corporal
- Posts: 52
- Joined: Sat Oct 16, 2004 11:40 pm
- Location: Arizona
-
- Officer - Brigadier General
- Posts: 3566
- Joined: Tue Oct 05, 2004 9:58 am
- Location: Tulsa,Oklahoma
The CA glue at your hobbyshop comes in different thicknesses and drying times.. This is what I typically use, but the stuff from Wally world will probably work just as well..Jagdflieger wrote:Is this significantly different from superglue that is purchased say in Wal Mart or Target?hworth18 wrote:Get some CA glue (superglue) from your local hobbyshop..
“The moment you think you know what’s going on in a women’s head, is the moment your goose is well and truly cooked”
-Howard Stark
-Howard Stark
-
- Corporal
- Posts: 52
- Joined: Sat Oct 16, 2004 11:40 pm
- Location: Arizona
Loctite is super strong but i find it takes too long to dry. Just use Krazy Glue. Tack the broken part on with the krazy glue and when you are satisfied it is in the right spot run a little stream of Krazy glue along the joined edge. Let it dry overnight then brush a little dullcote on to get rid of the shine of the Krazy Glue.
Wait at least overnight because if you dullcote too soon it will turn white from reacting with the krazy glue.
Wait at least overnight because if you dullcote too soon it will turn white from reacting with the krazy glue.
i never met an airplane i didn't like...
-
- Officer - Brigadier General
- Posts: 11238
- Joined: Tue Oct 05, 2004 7:38 pm
- Location: Central California
I'm with Aferg in using Krazy glue. I've used it successfully on a number of repairs and customizations and it holds very well! I initially used the liquid version but have now switched to the gel type as it applies easily and doesn't "run," getting glue over parts of the model and creating smudges. The gel also works well on porous surfaces, such as a break in plastic.
"If you fail to plan, you plan to fail."
- grunt1
- Officer - Brigadier General
- Posts: 2979
- Joined: Tue Jul 25, 2006 8:41 pm
- Location: Indiana
- Contact:
I use the 3 or 4 minute epoxy you can get in the auto section of Walmart. Bonds much stronger than superglue and works on many more surfaces.
It comes as a two cylinder syringe looking thing. The two tubes shoot out equal parts of the material that when mixed together create the bonding reaction.
Easyist way I have found is to squirt out a little onto some aluminum foil and mix it with a toothpick. Then use the same toothpick to apply the proper amount to the joint.
If you are committed to superglue, then you might prep the area (both sides) with some model cement first. It will destabilized the surface of the plastic allowing the superglue to mix in an get a better bond.
It comes as a two cylinder syringe looking thing. The two tubes shoot out equal parts of the material that when mixed together create the bonding reaction.
Easyist way I have found is to squirt out a little onto some aluminum foil and mix it with a toothpick. Then use the same toothpick to apply the proper amount to the joint.
If you are committed to superglue, then you might prep the area (both sides) with some model cement first. It will destabilized the surface of the plastic allowing the superglue to mix in an get a better bond.
-----------------------------------------------------------
-------- Need a list of everything 1:18? --------
---------- http://www.sshqdb.com --------------
---- Built by the community, for the community ----
-----------------------------------------------------------
My Store: http://www.battlegroundmodels.com
-------- Need a list of everything 1:18? --------
---------- http://www.sshqdb.com --------------
---- Built by the community, for the community ----
-----------------------------------------------------------
My Store: http://www.battlegroundmodels.com
-
- Officer - Brigadier General
- Posts: 11238
- Joined: Tue Oct 05, 2004 7:38 pm
- Location: Central California
Superglue will cause fogging when it dries -- but that is only when it runs onto surfaces when too much is applied. When Krazy glue is applied in the right amount so as not to run or overflow, you will not notice it. That's why I like the gel, as it doesn't runRogo wrote:Just curious, but doesn't Krazy Glue cause fogging of finished parts, or is that only with certain materials?
Rogo
"If you fail to plan, you plan to fail."
-
- Officer - Lt. Colonel
- Posts: 1230
- Joined: Wed Nov 09, 2005 7:58 pm
- Location: South Florida
The fogging from CA glue is requently due to finger/body oils on the area around the spot being glued. Wipe the surrounding area with alcohol before applying glue. I figured this out after I had a perfect fingerprint appear when using CA on one of my pieces.
If at first you don't succeed, try, try again. Then quit. No use being a damn fool about it.
-W.C. Fields
-W.C. Fields
-
- Officer - 2nd Lieutenant
- Posts: 363
- Joined: Wed Apr 27, 2005 10:06 am
- Location: Boynton Beach, Florida
- Contact:
I found a CA glue at my local hobby shop that is designed for plastics. So far I have had great results.
http://www.bsiadhesives.com/Pages/hobby/ca.html
It's the third item down called Maxi-cure.
http://www.bsiadhesives.com/Pages/hobby/ca.html
It's the third item down called Maxi-cure.
One hundred and fifty three - 1:18 scale aircraft on the ceiling looks :shock: damn good!
-
- Officer - Lt. Colonel
- Posts: 1230
- Joined: Wed Nov 09, 2005 7:58 pm
- Location: South Florida
Rogue wrote:FlPickupman the CSI!flpickupman wrote: I figured this out after I had a perfect fingerprint appear when using CA on one of my pieces.
CA will craze clear parts.
Fat lot of good it did me! I already knew who the fingerprint belonged to. lol
If at first you don't succeed, try, try again. Then quit. No use being a damn fool about it.
-W.C. Fields
-W.C. Fields
CA Glue Fogging
Hmmm...some information here about CA glues and the fogging issue. CA glues, like most glues, have a chemical reaction when they are exposed to air. Depending on the type of material they are in contact with, vapors due to this chemical reaction are produced. Plastics of just about any type can cause serious vapors, but paint on the plastic has caused the most in my model building past. This "frosting" is most apparent on clear plastics such as canopies. What I've learned is, once the CA is applied (and use it sparingly!), turn the piece so the glued surface is upper most, and then ventilate the area well while it cures. I have a small fan (salvaged from a computer) that I use to blow air across the surface and vapors away. As for the fingerprint problem, years ago we used to use CA glues on evidence. We built a "vapor box" from a fish tank. A wooden base with two 40 watt lightbulbs were placed apart and a soda can with the top cut off was slipped over each bulb. The bottom of the can (now facing up) was filled, one with a few drops of CA, the other with a few drops of water. The evidence was suspended above and between the two cans and the fish tank was inverted and placed over everything. When the lights in the cans were turned on, the heat vaporized the CA and the water. The CA attaches itself to the water vapor and changes it's chemical structure. The CA/water then attaches to oil from the skin on the evidence and hardens. The fingerprint is now clearly visible and nearly impossible to remove. Of coarse, the evidence is now perminently encased in a micro-thin layer of CA. We still use this method today (yes...I'm a working cop with 31 years behind me). Next class will be on Iodine fogging and butrite embedding. Questions?....class dismissed.
US Army MP Corps combat veteran Operation Desert Shield/Desert Storm
-
- Officer - Lt. Colonel
- Posts: 1230
- Joined: Wed Nov 09, 2005 7:58 pm
- Location: South Florida
-
- Corporal
- Posts: 52
- Joined: Sat Oct 16, 2004 11:40 pm
- Location: Arizona
-
- Sergeant
- Posts: 110
- Joined: Wed Oct 06, 2004 2:15 pm
- Location: NY